1000×22 mm CNC - Bending Roll

CNC 4R 1000x22 mm

4 Roll Dual Initial Pinch / 1000×22 mm CNC

4 ROLL HYDRAULIC MODEL 1000 x 22mm CNC EVO GRAPHIC 4AXIS PROG
capacity:
-Width of plate 1000 mm
-Thickness of plate 22 mm
-Pre-pinch 16 mm

minimum bending ID 230 mm
depend on thickness vs. plate yield

Rolls -Surface length mm. 1050
-top roll mm. 250
-lower roll mm.260

-Power electric 15Hp on centralized hydraulic unit , voltage 3ph Vac 400/50

Configuration installed

• Hardening of the 4 rolls , very high resistance against wear.
• Central rolls both driven powered with axial gearbox and direct drive hydraulic motor.
• Calibration system for the re-rolling of welded shells rounding unwanted flat spots.
• Console electric on wheels with centralized commands joysticks CNC position readout.
• Opening front side hydraulic drop-end unloading closed shells.
• CNC Digital position of the 4 rolls, CNC programmable 4 axis graphic CAM autocalc
• Variable speed on proportional valves stepless continuous controller.

4 Roll Dual Initial Pinch
plate roll latest technology, customizable configuration upon the different requirement of production: -Variable Geometry -Planetary Driven -Linear Guideways -Combination Pinch Pyramid -Double initial pre pinch

Section Bending Roll
Profiles bending machine, Angle bending roll, 3 and 4 roll configuration dua

3 Roll Heavy Duty
Heavy Roll Bending Machines 3 roll configuration variable geometry

Accessories Manipulators
supports and manipulators hydraulic operated with control manual and

Straightening Machines
Plate sheets straightening , Section bars and profiles straightenin

Cone roll
4 Roll Dual Initial Pinch

1000×22 mm CNC
4 Roll Dual Initial Pinch

3000×22 mm 4roll CNC
4 Roll Dual Initial Pinch

3000×16 mm Digital
3 Roll Pyramid Pinch

Limpet coil pipe
tube forming in half radius with rolling into spiral for applica

Prebend flange bar
stainless steel full bar on edge section pre-bend leading and tra

Stainless cone roll
thick 2 mm small dia. 80 mm SS plate film coated

Coil tube rolling
boiler heater pipe coil roll serpentine

MOS SLOVENIJA

IMTEX INDIA

EUROBLECH GERMANY

33.BI.MU FIERAMILANO

4 roll 500×20-30 mm cnc
4 Roll Dual Initial Pinch

2500×20 mm Faccin
3 Roll Pyramid Pinch

SHAFT 200mm MG
Profile Bending Roll

Shaft 180mm Sertom
Profile Bending Roll

4 Roll Dual Initial Pinchplate roll latest technology, customizable configuration upon the different requirement of production: -Variable Geometry -Planetary Driven -Linear Guideways -Combination Pinch Pyramid -Double initial pre pinch

Section Bending RollProfiles bending machine, Angle bending roll, 3 and 4 roll configuration dua

3 Roll Heavy DutyHeavy Roll Bending Machines 3 roll configuration variable geometry

Accessories Manipulators supports and manipulators hydraulic operated with control manual and

Straightening Machines*Plate sheets straightening , *Section bars and profiles straightenin

Cone roll4 Roll Dual Initial Pinch

1000×22 mm CNC4 Roll Dual Initial Pinch

3000×22 mm 4roll CNC4 Roll Dual Initial Pinch

3000×16 mm Digital3 Roll Pyramid Pinch

Limpet coil pipetube forming in half radius with rolling into spiral for applica

Prebend flange barstainless steel full bar on edge section pre-bend leading and tra

Stainless cone rollthick 2 mm small dia. 80 mm SS plate film coated

Coil tube rollingboiler heater pipe coil roll serpentine